Schedule And Pricing

 

What're your concepts on A Step-by-Step Guide to Installing a Bathtub?

Installing a bathtub isn't exactly brain surgery, but it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately difficult project. If the old tub is easily obtainable, the job can move quickly; if you need to open a wall surface to eliminate the old tub and also place the new bath tub, the job is much harder. In either case, the project is within a residence handyman's skills, although you will need a helper to vacate the old tub and also embeded in the new one. Ensure you have actually certified on your own for the work as well as fit trying it. Instead of employing a specialist to take control of a halfway-completed project, it is better to take into consideration employing one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly assist you install a new bath tub in your restroom if you have currently gotten a brand-new bathtub as well as do not need to transform the setup of your previous supply of water pipes.
Your devices and material list ought to comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, switch on the taps to drain any type of water continuing to be in the system. The process of removing the existing faucets can be fairly bothersome as a result of the restricted gain access to that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipes. Once the supply pipelines have been eliminated, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.

 

 

Fitting New Taps

If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Safeguard the faucet in place with the manufacturer provided backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type needs to be connected to the faucet finishes first, tightening just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Mounting the Bathtub

Using both wood boards under its feet, place the bathtub in the needed position. The wooden boards are handy in equally spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by examining the spirit level and also readjusting the feet on the bathtub till the spirit level reads level.
To set up taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipeline by making a compression join; after that do the same for the various other faucet.
Turn on the water and examine all joints and new pipework for leakages and tighten them if necessary. Fill the tub and also check the overflow outlet and also the regular electrical outlet for leakages.
Lastly, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling and securing around the tub ought to wait till the bathtub has been used a minimum of when as this will resolve it right into its final position.

 

 

Planning for the Installment

First of all, the sustaining framework provided with the bath should be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to stop strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to now prepare to be suited its last position.

 

 

Tiling Around the Bathtub

In the location where the bath meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to break a rigid seal, triggering the water to pass through the wall surface in between the bathroom as well as the tiling, leading to difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and installations. They are marketed in tubes and also cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked newspaper or soft rope. Remember to always load the bathtub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealant can crack rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily available on the market. It is suggested to fit the tiles using waterproof or waterproof sticky and also grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

As a person who reads about Tools You Need to Install a New Bathtub , I figured sharing that chunk was a smart idea. Do you know another person who is involved in the subject? Feel free to share it. Thank-you for going through it.

Book My Estimate